SinceVision Adds Wide-Spot Laser Displacement Sensor for Rough-Surface Metrology

The SGI-N030W uses an expanded laser spot and optical triangulation to stabilise displacement readings on textured surfaces, with in-line battery electrode thickness measurement as a lead application.

SinceVision has introduced the SGI-N030W, a wide-spot laser displacement sensor intended for high-speed, non-contact dimensional measurement on rough, textured and irregular surfaces. The unit extends the company's SGI Series portfolio and is aimed at lithium-ion battery manufacturing, semiconductor processing and precision mechanical engineering, where reliable micrometre-level measurement is a requirement.

Wider spot, steadier signal

Conventional point-spot laser displacement sensors concentrate reflected laser energy onto a small area, which makes readings sensitive to microscopic surface features such as scratches, grain boundaries, brushed textures and matte finishes. SinceVision says these characteristics can produce signal variations that are interpreted as dimensional change, potentially triggering false defect warnings and extra inspection work.

The SGI-N030W addresses this through a wide-spot optical configuration. By collecting reflected light across a broader surface area, the sensor averages localised microscopic peaks and valleys before signal conversion, which the company says reduces the influence of surface roughness and optical scattering. Target materials include drawn metals, sandblasted surfaces and coated battery foils, measured using optical triangulation.

Specified performance

  • Reference distance of 30 mm with a measurement range of ±5 mm
  • Repeatability of 0.05 µm on a diffuse white target under static conditions, as specified by SinceVision
  • Linearity of ±0.02% of full scale across the measurement range
  • 50 kHz sampling frequency, equivalent to a 20 µs update interval
  • RS485, 100Base-TX Ethernet and switchable analogue outputs of 4–20 mA current or 0–10 V voltage
  • Master-slave synchronisation so two sensors can operate in opposition from either side of a component or moving material

In-line electrode thickness

One of the principal applications identified by SinceVision is in-line thickness measurement of lithium-ion battery electrodes, where coating thickness and uniformity affect energy density, internal resistance and long-term cell stability. The company notes that offline inspection with contact micrometers or drop indicators can introduce operator variability and may deform wet or uncured electrode material, while periodic spot checks cannot give continuous coverage across a full production reel.

The proposed arrangement uses two synchronised sensors positioned above and below a moving electrode web, mounted on a calibrated, low-thermal-expansion marble gantry. Each head measures its clearance to the material, and a system controller combines those readings with the fixed mounting datum to calculate absolute electrode thickness in real time. According to SinceVision, production trials demonstrated stable, repeatable thickness measurement within ±0.3 µm at a web speed of 300 mm/s. The company states that the 50 kHz sampling rate provides high longitudinal resolution, allowing detection of localised coating agglomerations, edge thinning and exposed substrate before the material reaches cell winding.

Semiconductor and motion applications

The sensor is also intended for semiconductor manufacturing, where non-contact measurement matters when handling sensitive wafer surfaces. Potential uses listed include wafer position verification, edge detection, height measurement and checks of wafer seating and chuck alignment in atmospheric transfer modules and vacuum load-lock systems.

In precision assembly, the device can monitor the dynamic movement of voice coil motors, linear actuators and micro-steppers. Its 50 kHz sampling rate is intended to capture transient displacement, mechanical oscillations, settling behaviour and end-stop overshoot across the full measurement range, with position data sent to machine control systems over Ethernet for real-time monitoring and process control.

Surface errors in the field

Jack Li, Global Sales and Marketing Director at SinceVision, says false defect warnings caused by surface texture remain a recurring challenge in battery manufacturing and precision assembly. He explains that conventional point-beam laser sensors can interpret microscopic scratches and rough coatings as actual thickness variations, slowing production lines and creating a need for additional manual inspection. The SGI-N030W's expanded optical spot is designed to average out these surface-related variations, while synchronisation between opposing heads supports high-speed thickness verification.

ZI

Zorica Ilic

Zorica Ilic is a network test, infrastructure, and sourcing editor covering OTDRs, optical power meters, spectrum analyzers, outdoor cabinets, patch panels, and splice closures for carrier and enterprise networks. Her articles explain calibration traceability, OTDR dynamic range in dB, insertion and return loss, IP codes, and operating-temperature ranges, while checking the edition and test setup behind each cited method or standard. She supports test teams, infrastructure operators, integrators, and procurement groups comparing compatibility evidence, spares, lead time, and replacement risk.